PDA

View Full Version : [ubuntu] Linksys WUSB11 V2.6 802.11b Adapter



rkphibb
February 4th, 2009, 02:17 AM
I have read through all of the links I can find including:

https://help.ubuntu.com/community/WifiDocs/Driver/Ndiswrapper

I installed CVS as detailed here:

https://help.ubuntu.com/community/WifiDocs/Device/LinksysWUSB11

and played around here:

http://ubuntuforums.org/showthread.php?t=943848

I have no security, ESSID is simply linksys

Here are my outputs:

lsusb
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 003: ID 077b:2219 Linksys WUSB11 V2.6 802.11b Adapter
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 058f:9360 Alcor Micro Corp. 8-in-1 Media Card Reader
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

/etc/network/interfaces
auto lo
iface lo inet loopback

auto wlan0
iface wlan0 inet dhcp
wireless-essid linksys

sudo iwlist wlan0 scan
wlan0 Scan completed :
Cell 01 - Address: 00:12:17:03:3E:AA
ESSID:"linksys"
Mode:Master
Channel:6
Encryption key:off
Signal level=90/100
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
24 Mb/s; 36 Mb/s; 54 Mb/s


ndiswrapper -l
lswlusb : driver installed

Latest version of ubuntu: uname -a
2.6.27-11-generic #1 SMP Thu Jan 29 19:24:39 UTC 2009 i686 GNU/Linux

sudo dhclient wlan0
Internet Systems Consortium DHCP Client V3.1.1
Copyright 2004-2008 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/

Listening on LPF/wlan0/00:06:25:08:37:77
Sending on LPF/wlan0/00:06:25:08:37:77
Sending on Socket/fallback

DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 4
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 11
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 9
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 13
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 2
No DHCPOFFERS received.
No working leases in persistent database - sleeping.

sudo ifconfig wlan0
wlan0 Link encap:Ethernet HWaddr 00:06:25:08:37:77
inet6 addr: fe80::206:25ff:fe08:3777/64 Scope:Link
UP BROADCAST MTU:1500 Metric:1
RX packets:26230 errors:0 dropped:0 overruns:0 frame:0
TX packets:8240 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5239558 (5.2 MB) TX bytes:1120596 (1.1 MB)


What am I missing? Can anyone steer me in the right direction?

Thanks.

rkphibb
February 4th, 2009, 02:27 AM
Oh I forgot this:
lspci
00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 200 Host Bridge (rev 01)
00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:11.0 IDE interface: ATI Technologies Inc IXP SB400 Serial ATA Controller (rev 80)
00:12.0 IDE interface: ATI Technologies Inc IXP SB400 Serial ATA Controller (rev 80)
00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80)
00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80)
00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (rev 80)
00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 82)
00:14.1 IDE interface: ATI Technologies Inc IXP SB400 IDE Controller (rev 80)
00:14.2 Audio device: ATI Technologies Inc IXP SB4x0 High Definition Audio Controller (rev 01)
00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80)
01:05.0 VGA compatible controller: ATI Technologies Inc RC410 [Radeon Xpress 200]
02:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
02:04.0 Communication controller: Conexant Systems, Inc. HSF 56k Data/Fax Modem

rkphibb
February 4th, 2009, 02:37 AM
More output

lshw -C network
WARNING: you should run this program as super-user.
*-network
description: Ethernet interface
product: RTL-8139/8139C/8139C+
vendor: Realtek Semiconductor Co., Ltd.
physical id: 2
bus info: pci@0000:02:02.0
logical name: eth0
version: 10
serial: 00:16:76:b3:c0:07
width: 32 bits
clock: 33MHz
capabilities: bus_master cap_list ethernet physical
configuration: broadcast=yes driver=8139too driverversion=0.9.28 ip=192.168.1.104 latency=64 maxlatency=64 mingnt=32 module=8139too multicast=yes
*-network:0
description: Wireless interface
physical id: 2
logical name: wlan0
serial: 00:06:25:08:37:77
capabilities: ethernet physical wireless
configuration: broadcast=yes driver=at76_usb driverversion=0.14beta1 firmware=1.101.2-84 wireless=IEEE 802.11b
*-network:1 DISABLED
description: Ethernet interface
physical id: 3
logical name: pan0
serial: 4e:9b:c9:c4:dd:fb
capabilities: ethernet physical
configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A multicast=yes

rkphibb
February 4th, 2009, 02:41 AM
I think my problem lies here?

dmesg | grep -e ndis -e wlan
[ 15.484560] at76_usb: wlan0 disconnecting
[ 16.438742] at76_usb: registered wlan0
[ 98.616026] wlan0: no IPv6 routers present

rkphibb
February 4th, 2009, 04:54 AM
I fixed this.

Any help???

ndiswrapper -l
netusb : driver installed
device (077B:2219) present (alternate driver: at76_usb)

rkphibb
February 4th, 2009, 04:56 AM
And this

dmesg | grep -e ndis -e wlan
[ 13.127993] at76_usb: registered wlan0
[ 14.080699] ndiswrapper version 1.53 loaded (smp=yes, preempt=no)
[ 14.126176] usbcore: registered new interface driver ndiswrapper

mb_webguy
February 4th, 2009, 05:29 AM
It looks to me that the at76_usb is claiming your wireless. Is that the driver you're trying to use? Have you followed the ndiswrapper troubleshooting guide (http://ubuntuforums.org/showthread.php?t=885847)?

rkphibb
February 4th, 2009, 03:28 PM
It looks to me that the at76_usb is claiming your wireless. Is that the driver you're trying to use? Have you followed the ndiswrapper troubleshooting guide (http://ubuntuforums.org/showthread.php?t=885847)?

Yes I believe that's the driver I am trying to use and yes I went through the troubleshooting guide. Does anything in my output look wrong?